When two fabric quotes sit side by side, most buyers compare price per metre and minimum order first. Almost nobody starts with width, even though width is one of the biggest levers on the number that actually matters: what the fabric in one finished garment costs. Two cloths at the same price per metre can land at very different costs per piece once your cutting room lays out a marker. This article explains marker efficiency in plain language, shows how width moves the calculation, and lists the width questions worth settling before you place an order.
What marker efficiency actually means
A marker is the layout plan for cutting: all the pattern pieces for a garment, arranged across and along the fabric so the cutter can slice through as many pieces as possible in one pass. Marker efficiency is simply the share of the fabric surface that ends up covered by pattern pieces. The rest is waste: the gaps between pieces, the strips along the selvedges, and the offcuts where the pattern does not interlock cleanly.
Efficiency is never one hundred per cent. Pattern pieces are curved and irregular, seam allowances eat into the edges, and some pieces simply cannot nest tightly against their neighbours. For a straightforward woven garment, a well-planned marker commonly lands somewhere in the 80–90 per cent range; a difficult layout with large asymmetric panels can fall well below that. The exact figure depends on the pattern and the cutting method, not on the fabric alone, which is exactly why width matters so much.
How width changes fabric consumption per garment
Picture a simple woven shirt. Say the main body pieces can nest two across on a cloth of about 140 centimetres usable width, but nest three across on a cloth of about 160 centimetres. In the first case, the cutting room needs one and a half marker lengths to cut three garments. In the second, one marker length yields all three. Per garment, consumption drops by a third of a marker length, and nobody has negotiated a single cent off the price per metre to get there.
That example is illustrative, but the logic behind it holds for real patterns: when pieces fit across the width in whole numbers with little leftover strip, consumption per garment falls sharply. When the width forces an awkward fit, say one large panel plus a useless narrow strip, every garment carries that strip as waste.
This is why experienced pattern makers think in ways across: how many pattern pieces, or how many complete garment sets, fit across the usable width. A width that lets pieces interlock, with one garment's sleeve slotting into the space left by the next garment's body, is worth far more than raw surface area suggests.
The catch: wider cloth is not automatically cheaper
Width is not free. A wider cloth carries more yarn in every metre, so it is priced higher per metre. The comparison that matters is therefore not price per metre but cost per garment: wider cloth at a higher price per metre can still come out cheaper per piece if the marker runs more efficiently. Equally, if your pattern only needs a narrow layout, paying for extra width you cannot use is pure loss.
There are practical limits as well. Very wide cloths can be harder to handle on some cutting lines, and certain garment types gain little from extra width beyond a point. The right width is pattern-specific, which is why it should be decided with a marker in hand, not guessed at the quotation stage.
Full width versus usable width
When a supplier quotes a width, ask what is actually usable. The full width of a finished fabric includes the selvedges, which are denser and not cut into. Usable width, sometimes quoted as usable for cutting, is the width your marker can rely on. Depending on the fabric construction, the difference can be several centimetres, and a few centimetres across an entire marker is often exactly the margin that decides whether one more piece fits across.
Width is also something that can drift from roll to roll, so it should be measured rather than assumed. Our inspection follows the ASTM D5430 four-point system, roll by roll, and inspection records are available per batch. If width consistency matters to your marker, say so in the brief and ask that it be measured and reported with the batch records.
Finishing and shrinkage move the width
Width is not fixed from greige to garment, either. Fabrics can lose or gain width through dyeing, finishing, washing and relaxation. If your garments are cut after a wash process, the width that matters is the width after your wash test, not the figure printed on a swatch card. This is one more reason to run a trial marker on actual finished cloth rather than on a paper assumption, and one more reason the fabric brief should state the width the pattern needs after finishing.
A practical checklist before you fix a width
- State the target usable width in your fabric brief, alongside composition, weight and end use, so the supplier matches qualities to your pattern instead of assuming.
- Ask whether the quoted width is full width or usable width, and how it is measured.
- Compare quotes on cost per garment, not per metre. Share your pattern consumption or marker plan so both sides calculate the same thing.
- Order enough sample length for a real trial marker before bulk, especially for new patterns or new suppliers.
- Ask that width be recorded during inspection, and that the records stay available per batch.
How this works at Mientex
We are a fabric supplier working between buyers and named partner mills, dealing in dyed and yarn-dyed natural-fibre fabrics: linen, cotton, linen/cotton blends, lyocell, wool blends and stretch qualities. Width sits alongside composition, weight and hand feel in the way we present qualities, and development starts from 50 metres per colour, so it is realistic to trial a width against a real marker before committing to bulk quantities. Lab dips take 5–7 days against a Pantone TPX/TCX standard or a physical swatch, and approval swatches are cut from the actual bulk batch, so the cloth you lay out in the trial is the cloth that ships.
If you are weighing one width against another, send the pattern, the target consumption and the end use to [email protected]. We will suggest qualities in widths that fit your marker and confirm what can be developed or supplied from stock.