A buyer opens a spec sheet and reads: 100% linen, 170 gsm. That number then travels into a costing sheet, a tech pack, a purchase order and, three months later, possibly a claim. It is worth slowing down at the first step, because 170 gsm is not one number. It is the average of a distribution, taken from a particular piece of cloth, in a particular state, by a particular method. Most arguments about fabric weight are really arguments about which of those four things nobody wrote down.

What the number measures, precisely

GSM is grams per square metre, and the test is almost aggressively simple. A circular cutter stamps out a sample of a fixed area, usually 100 square centimetres, the sample goes on a calibrated balance, and the reading is scaled up to a square metre. The same reading, converted, becomes ounces per square yard, which is still how a good number of British and American buyers think: divide grams per square metre by 33.906, or multiply ounces by the same figure to go the other way.

Everything that makes the number arguable sits inside that simplicity. The sample is small, so it represents one patch of one metre of one roll. The balance is only as good as its last calibration. And the cloth itself is not a stable object: it takes up and gives off moisture with the room it is sitting in, and it changes density when it is washed, dyed, stretched or pressed.

Why the same nominal weight arrives heavier or lighter

Greige weight and finished weight are different weights

Greige cloth straight off the loom is not the cloth the garment maker receives. Dyeing and finishing can add mass, remove mass, or redistribute it. Aqueous processes and shrinkage usually push weight up; tension, stentering and the various finishing passes can pull the cloth out and bring grams per square metre down. This is why a quotation that says only 170 gsm is incomplete. The useful question is which state that figure describes, and whether the finished weight will be checked against it.

Moisture regain moves natural fibres more than synthetic ones

Cotton, linen, wool and lyocell all hold water inside the fibre. In a humid inspection room a linen will read heavier than the same linen in a dry one, and the difference is not trivial at the scale of a purchase order. This is the single most common reason two people weigh the same quality and disagree. Testing in a conditioned room, and writing the conditioning into the inspection record, removes most of the argument before it starts.

Position on the roll, and position in the batch

Selvedge to centre is not perfectly uniform. Neither is the first metre of a beam compared with the last. A single cutter sample tells you what one patch weighs; a proper check takes samples from several places and treats the spread as information rather than noise.

Relaxation after the first wash

Cloth that has been under loom or finishing tension will move when it is wetted out and dried without tension. Weight per square metre can rise as the cloth shrinks in both directions. If the garment will be washed before it reaches the customer, the number that matters is the one after that wash, measured the same way.

The tolerance belongs in the order, not in the argument

No mill delivers a weight that lands on the nominal figure in every roll, and no supplier working with mills can promise otherwise. What matters commercially is that the acceptable band is agreed in writing before bulk begins, that the test method is named, and that both sides know which state of cloth is being measured. A tolerance that is merely assumed is a tolerance that will be disputed.

What weight suggests about end use

Weight is a rough first filter, and it is useful as long as it is treated as one. Light cloth, broadly the blouse and lining end of the range, goes into soft dresses, shirtings and anything that needs to move. The middle of the range, where most commercial shirting and lightweight trouser cloth sits, carries the bulk of woven business. Heavier cloth above that is trousers, soft tailoring, workwear and jackets, and it behaves differently on the machine as well: heavier fabric means fewer metres per roll, more feed and needle problems, and a different seam finish.

Three cautions. Weight bands overlap between fibres, because linen feels cooler and drier than cotton at the same weight. Weight says nothing about cover, and a loose weave can be heavy and still show skin. And weight says nothing about durability, which is a function of yarn quality, twist and construction rather than mass.

Two cloths at the same weight are not the same cloth

A plain weave and a twill can both weigh 180 gsm and behave nothing alike. Yarn count, twist, ends and picks per unit length, and the weave structure all sit underneath the single weight figure. This is why a brief that specifies only grams per square metre can get you a technically compliant cloth that is wrong for the garment. Ask for the construction as well: yarn count in both directions, sett, weave, and the finish applied.

Where weight shows up in cost

Fabric is bought by length and consumed by area, and weight is the bridge between the two. For a given width and fibre, a heavier cloth uses more yarn per metre, so it costs more per metre at the same yarn price. It also changes marker efficiency, because heavier cloth is less willing to be squeezed into a tight lay. Two quotes at the same price per metre for different weights are not comparable, and a quote that is cheaper because the cloth is lighter is not a saving if the garment no longer hangs correctly.

What to write in the brief instead of a bare number

None of this is complicated, but all of it has to be written down before the first metre is dyed. If you are setting a weight band for a new quality and want a second opinion on whether it will behave the way your garment needs, send the construction and the end use to [email protected] and we will tell you plainly what the cloth will and will not do.