Most fabric quotations go through two or three rounds not because the price was wrong, but because the brief was incomplete. A supplier can only quote what you specify: when weight, width, colour standard and quantity are missing or vague, the quote you receive is an estimate built on assumptions, and the number changes the moment those assumptions get corrected. Writing a proper brief is not paperwork for its own sake. It is the shortest route to a price you can actually plan against, and to a sampling round that answers the questions you care about.

What the brief must contain before anyone can quote

Composition and construction

Start with fibre content, stated precisely. "A linen cotton blend" is not a specification; "55% linen, 45% cotton" is. If you know the construction you want, name it: a plain weave shirting, a heavier twill, a yarn-dyed check. If you do not know the construction, describe what the fabric has to do instead, the garment category, the season, the hand you are after, and any reference cloth you can send or point to. A supplier can propose constructions, but only if the brief explains what the fabric must achieve. The more concrete the description, the closer the first proposal lands.

Weight, width and finish

Weight in GSM and usable width are the two numbers every quotation is built on, so both belong in the brief. If the weight is a target range rather than a fixed number, say so: a brief asking for "around 180 GSM in a usable width of at least 140 cm" gives the mill room to propose something they actually weave well, and gives you a quotation that is comparable across suppliers. Mention finishing expectations too, such as enzyme wash or a fabric that needs to be suitable for garment dyeing, because finishing choices affect both price and planning.

Colour direction

If colour matters to the programme, name the standard in the brief: a Pantone TPX or TCX code, or a physical swatch you will courier. On our side, lab dips are developed in 5 to 7 days against either reference. What stalls colour development is a brief that says "match the photo" or points at a colour that exists only on a screen, because screens shift and nobody can quote confidently against a colour that has not been fixed. Naming the standard in the brief does not slow development down; it removes the most common reason a development round gets repeated.

Quantity: be honest, and say what the number is for

Quantity is where briefs most often mislead, usually by accident. A buyer writes an optimistic annual figure, receives a price that assumes it, and then finds the real first order is a fraction of that. State three separate numbers instead: the sampling quantity, the realistic first bulk estimate, and the annual potential if the style works. That lets a supplier price honestly at each stage instead of defending a number nobody believes.

Be equally explicit about what counts as a development quantity. Our minimum for stock qualities and most dyed orders is 50 metres per colour, and it is the reason small programmes can develop properly instead of being pushed aside. Embroidery and special finishes may carry higher minimums, which is exactly why they must be flagged in the brief rather than discovered after the quotation. A quote built on an honest quantity is more useful than one built on a hopeful number that never materialises.

Compliance and documentation belong in the brief, not after it

If the garment needs certification, say which one. GOTS, GRS and OCS coverage is available through certified partner mills, with transaction certificates issued in the buyer's company name and travelling with the goods. If testing will be required, name the scope: colour fastness to ISO or AATCC methods, fibre composition, restricted substances screening. Third-party tests through SGS, Intertek or Bureau Veritas are arranged per order, with reports issued in the buyer's name, so the brief should state what the reports need to cover. If inspection matters, say so as well; every roll can be inspected on the 4-point system under ASTM D5430, and a buyer who asks for that in the brief gets it priced and planned rather than negotiated late.

Trade terms are part of the brief too. FOB, CIF and EXW produce different numbers, and a quote that does not state its basis cannot be compared fairly. If payment will start with a T/T deposit on a first order, acknowledging that in the brief saves a round of clarification. And if you plan to consolidate several qualities into one shipment with one document set, put that in the brief: consolidation changes how a supplier builds the quotation, and it is much easier to plan when it is requested upfront.

What a complete brief gets back

A brief covering composition, weight and width, colour standard, honest quantities, compliance requirements and trade terms should come back with four things: a price quoted on the basis you specified; a realistic lab dip timeline rather than a guess; minimums stated plainly, including any that apply to special finishes; and an inspection and testing plan that matches what you asked for. If any of those four comes back vague, that itself is information about the supplier, and it costs you nothing to have found it in the brief stage.

A short checklist to reuse

None of this takes long to write, and every line removes one assumption from the supplier's side. If you want a second pair of eyes on a brief before it goes out to mills, send it to [email protected] and we will tell you what is missing before it costs you a quotation round.