Most buyers specify "cotton jersey with a bit of stretch" and only discover at fit stage that the cloth they approved and the cloth they received behave like two different fabrics. The variable responsible is usually elastane content, and it is rarely written on a quotation to the precision that matters. Two percent and six percent elastane are not the same product at any stage: not in the greige, not in the dyehouse, not on the cutting table, not after twenty washes.

The percentage chooses the category before it chooses the hand

Stretch fabrics sit in loose bands, and each band has a default end use. Reading the percentage first tells you which questions to ask next, and it also tells you when an offer does not make sense. A jersey quoted at twelve percent elastane for a basic t-shirt is not generous, it is mismatched: heavier in the hand, harder to press, and more expensive than the garment needs.

Two to four percent: comfort stretch

The fabric still behaves like a natural-fibre cloth. Shirting, poplin, fine twill, light jersey and trousers live here. The stretch lets a woven garment move with the body rather than holding it, so creases press, seams behave and a tailor can still work the cloth. If you want stretch without changing the look of a cotton or linen piece, specify this band.

Five to eight percent: action stretch

At this level the cloth feels elastic rather than merely forgiving. Stretch denim, close-fitting dresses, leggings-weight jersey and casualwear sit here. Recovery becomes a design requirement: the fabric has to come back to its original width after being pulled, or knees and seats bag out before the season ends. Weight and compactness usually rise with the percentage, because more elastane needs more cover.

Ten to fifteen percent: high stretch and shaping

Now the elastane does structural work. Bodysuits, contour panels and close-fitting knitwear use this band. Patterns must be drafted for the stretch, seam types change, and behaviour under a needle becomes a production issue rather than a design detail. Expect a longer development cycle.

Eighteen percent and above: swimwear and compression

At the top of the range the fabric is a different material system, usually a fine gauge base with elastane running through it, often paired with a second fibre for chlorine or sunlight resistance. Colour, shrinkage and heat sensitivity all have to be handled on the fabric's terms, and the end use should be stated before the first lab dip is requested.

Recovery is the number that actually matters

Buyers ask how much a fabric stretches and rarely ask how well it returns. The first question is easy to answer with a ruler and two hands. The second one determines whether a garment survives a season. A cloth that extends thirty percent and recovers to within two percent of its original width is a better product than one that extends fifty percent and stays stretched after a wash. Stretch without recovery is distortion with a delay.

Cheap substitution shows up here first: a lower-grade elastane with a heavier finish can hit the stretch target, pass a showroom hand check, then grow in length after the first domestic wash. For fitted garments, ask for stretch and recovery figures on the test report, not the quotation.

Heat is what breaks a stretch fabric

Elastane is sensitive to heat, and almost every wet process in a dyehouse involves heat. Dyeing, drying, heat setting and pressing all interact with the elastane, and the order and temperature of those steps affect final width, final hand and final recovery. Two batches of the same base cloth can leave finishing at different widths when the route differs, even with a matching dye recipe.

Two practical consequences follow. Width on a stretch quality is a tolerance to be agreed, not a fixed number to be assumed. And when a shade is re-developed on a new base batch, ask whether the finishing route stays the same, because the shade may match while the width and hand do not.

Colour, shrinkage and the weight you did not order

Higher elastane content tends to pull cloth in during finishing, which raises grams per square metre even when the yarn count has not changed. A buyer who approved a lighter swatch and receives a heavier roll is often looking at a width difference, not a yarn difference. That also explains why shrinkage figures belong next to the width tolerance, and why a garment cut from an approved swatch can come up short when bulk arrives.

Deeper shades generally need more dye and more time in the bath, and the cloth that leaves deepest in colour is also the cloth that took the most heat. On a range mixing pale and deep shades on one stretch base, the two may not finish at identical widths. Planning for that at sampling stage is far cheaper than finding it at cutting.

What to ask for in testing and documents

Stretch is not covered by a single certificate, so the useful question is not "is it certified" but "what was tested, on which batch, and by whom".

Third-party testing through SGS, Intertek or Bureau Veritas can be arranged per order for colour fastness, composition and restricted substances, with reports issued in the buyer's name and shipped with the goods. Certification such as GOTS, GRS, OCS, Lenzing or BCI is available through certified partner mills, with transaction certificates issued in the buyer's name. None of those tells you whether recovery is good; that comes from the test report and your own wash trial.

Placing the order: what changes once you pass five percent

Below five percent, a stretch quality can be handled like any other natural-fibre fabric in the programme: greige and selected dyed batches held in stock, laboratory dips in five to seven days against a Pantone TPX or TCX reference or a physical sample, and a minimum of fifty metres per colour for stock qualities and most dyed orders. Above that, cloth is more often developed for the order, embroidery and special finishes may carry a higher minimum agreed in advance, and the approval swatch cut from the bulk batch matters more rather than less, because it is the only physical record of the width, hand and shade produced.

Where a range mixes several stretch qualities into one delivery, they can usually be consolidated into a single shipment with one set of documents under FOB, CIF or EXW terms. That saves freight, but the latest quality sets the shipping date, so confirm the stretch items first rather than last.

A short checklist before you approve the strike-off

If you are developing a stretch quality and are unsure which band your garment belongs in, send the end use, the target weight and the reference swatch to [email protected], and we will reply within one working day with the options that fit and the ones that do not.